Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
Just how do you feel about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard task. If the old bathtub is conveniently easily accessible, the job can move rapidly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified yourself for the job and fit trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have already acquired a brand-new tub and also do not need to transform the plan of your previous supply of water pipelines.
Your devices and material checklist need to consist of the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the called for placement. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads level.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the tub ought to wait until the tub has actually been made use of at the very least when as this will settle it into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the faucet and the sink. Protect the tap in position with the producer given backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind must be attached to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a stiff seal, creating the water to permeate the wall between the bath and also the tiling, resulting in problems with dampness and possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture rather very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads on How to Install a Bathtub Yourself, I figured sharing that excerpt was beneficial. Liked our review? Please share it. Let other people discover it. Kudos for your time. Please check our blog back soon.
Book Now!
Report this page